How to Design a Simple LED Circuit

By Editorial Team

Updated September 28, 2017

Items you will need

  • LED's

  • Resistor

  • Battery or power source

  • Wire or alligator clips

  • Helpful to have (multimeter)

  • Helpful to have (soldering iron)

Design a Simple LED Circuit
i lifeengineer

LED circuits are very easy to design. An LED or Light Emitting Diode, is a very low current light source that is very safe and durable for use in your project. This article will show you how to design and build a very simple LED circuit.

Select the number of LED's you want in your project

The first step is to choose how many LED's you want to light and their type (color, brightness). With this simple circuit you will be somewhat limited by the amount of voltage that can be safely provided for your project.

Calculate the amount of voltage you need from your power supply.

Look for the "diode forward voltage" specification from the manufacture's website or packaging. If you do not have this information you can use the following to estimate:

Red or Orange 2.0 V Yellow 2.1 V Green 2.2 V True Green, Blue, White 3.3 V Blue (430 nm) 4.6 V

Say you want to have 3 Red LED's in your circuit. Only use the diode forward voltage value. So, 3 x 2.0 = 6V, needed.

Easy way to get 9 volts

Once you have the required voltage, choose how you want to power the circuit. Do you want to plug it into an outlet and not have to change batteries or do you want the freedom to move around?

DC voltage works easiest. AA, AAA, or 9V batteries are cheap and easy to find for a simple project. The simplest way to use AC as your source is a wall plug (wall wart), the large black plugs that come with most every electronic device you purchase. You probably have a box full of these sitting around. You will have to cut the plug off the end of the cord. Use a multimeter to determine the positive and negative lead.

AC voltage can also be designed in the circuit. AC will only drive the LED half of the time since the voltage travels in waves. A full-wave bridge rectifier can be used to fully power LED's. This is essentially what the wall wart is doing for you.

Find a power supply greater than the calculated diode forward voltage value from step 2. In our case we calculated 6 volts. A power supply value greater than 6 volts will be needed. If you are driving a large number of LED's, current may also be important.

Calculate the required LED resistor value.

LED's cannot be connected directly to the battery or power supply. The LED will be instantly destroyed because the current is too great. The current must be reduced. The easiest way to do this is by using a resistor. Calculate the LED resistor value with the following formula:

LED Resistor Value, R=(supply voltage - LED voltage) / LED current

In our example:

Say we use a 9V battery, then supply voltage = 9V. LED voltage for red LED's, from Step 2 is 2.0 V LED current is 20 mA (this is a typical value if not provided by the manufacturer)

If the resistor value is not available, then choose the nearest standard resistor value which is greater. If you want to increase the battery life you can select a higher resistor value to reduce current. The reduced current will result in a dimmer LED.

R = (9 - 2.0) / 20 mA = 350 ohms, use the next higher standard value = 360 ohms

You can keep your project organized by using a small PCB available at Radio Shack

Wire your circuit together.

You can soldier the wires directly together, use crimp connectors, or use a small circuit board. Choose the best method based on the size of your project.

Success!

The final step is to mount the LED's in your project. Radio Shack and others sell chrome or plastic LED holders that make a professional looking mount easy. You can add momentary push buttons or on/off switches to your LED circuits.

Designing and building a simple LED circuit is an easy project.

Tips

The longer lead on the LED is the positive side. Do not reverse the leads on the LED. Remember that if you do not have the right resistor value handy you can put more than 1 resistor in series and add their values to get total resistance.

Warnings

Make sure if you using AC with a full-wave rectifier to consider the voltage drop. Measure the output with a multimeter to be sure. Never connect the LED's in parallel Always use caution when working with power sources and soldering iron. They can be dangerous.

×